x (x)

Gifts for Woodcarvers

Gifts for Woodcarvers

Page:
  1. 1
  2. 2
Grid  List 
  1. Auger Gimlets: set of 7

    £9.90

    Auger gimlets are a classic tool commonly found in hand tool woodworkers toolchests. They are used for drilling small holes, typically for pre-drilling screw holes to prevent the wood from splitting when the screw is driven, but they can be used anywhere a small neat hole is required.

    Gimlets are great fun to use, ideal for kids and are a useful lightweight drill for bushcraft and green woodworking.

    Sizes included in the set: 2...

  2. Out of Stock

    Narex Set of 6 Profi Carving Chisels

    £158.50
    Narex Set of 6 Carving Chisels handles 145mm long European Beech stained and waxed octagonal barrel Chrome-silicon alloy steel heat treated Hardness 59 +/- 1 HRc Blades are sharpened and lapped with abrasive paste and arkansas stone & hand polished Excellent value professional quailty starter set of carving chisels ...
  3. Narex - Boxed Set of 8 Profi Carving Chisels

    £234.50
    Narex - Boxed Set of 8 Profi Carving Chisels handles 145mm long European Beech stained and waxed Octagonal barrel Chrome-silicon alloy steel heat treated Hardness 59 +/- 1 HRc Blades are sharpened and lapped with abrasive paste and arkansas stone & hand polished...
  4. Workshop Heaven Hand Stitched Threesquare Rasp 150mm No.4 (38tcm)

    £29.50

    Used for working small flats, cutting grooves and forming acute internal corners down to 60 degrees, the triangular section and finely toothed corners of the threesquare rasp makes it a versatile favourite.

    Face width: 9mm tapering to 5mm at the tip   Coarseness: 38 teeth per square cm (medium)

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel is carefully gro...

  5. Workshop Heaven Hand Stitched Hand Rasp 150mm No.3 (28tcm)

    £26.50

    A fairly aggressive hand rasp for initial shaping of flat or convex surfaces. Both faces of the rasp are toothed right up to the edges.

    Face width: 15mm x 2.5mm,   Coarseness: 28 teeth per square cm (medium/coarse)  

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel is carefully ground and ‘fined’ to a smooth surface before being strapped to a...

  6. Workshop Heaven Hand Stitched Square Rasp 150mm No.4 (38tcm)

    £29.50

    Square rasps are invaluable for forming angular shapes from round ones – forming a square or arched hole from a drilled one is the classic example.

    The 150mm square rasp has a tapered tip and a slender 5mm square section, so it is easy to get started into holes of 7mm or larger. 

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel is carefully ground and &lsquo...

  7. Out of Stock

    Workshop Heaven Hand Stitched Cabinet Rasp 250mm No.3 (14tcm)

    £46.50

    Long, broad, and highly efficient, this coarse rasp is used for initial shaping of larger workpieces like table legs, arched aprons or large sculptural pieces.

    Shoulder to tip: 250mm ,  Face width: 28mm,  Coarseness: 14 teeth per square cm (coarse). 

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel is carefully ground and ‘fined’ to a smooth ...

  8. Workshop Heaven Hand Stitched Half Round Rasp 250mm No.4 (20tcm)

    £46.50

    The final stage of rough shaping, the halfround profile can get into tighter radii than the cabinet and the No.4 (coarse / medium) toothing gives more controlled material removal and a finer surface as you gradually sneak up on your lines.

    Face width: 25mm,  Coarseness: 20 teeth per square cm (medium/coarse).  

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel...

  9. Workshop Heaven Hand Stitched Hand Rasp 250mm No.2 (10tcm)

    £44.50

    A vicious stock remover for hogging away waste on flat or convex surfaces with minimum effort, this heavy rasp is a delightful tool to work with.

    Face width: 24mm x 5mm,  Coarseness: 10 teeth per square cm (very coarse).  

    Each Workshop Heaven hand stitched rasp begins life as a forged and annealed blank of high carbon tool steel is carefully ground and ‘fined’ to a smooth surface before being strapped to ...

  10. Narex Spoon Making Carving Tool - Small Right

    £28.80
    Narex Spoon Making Carving Tool - Small Right...
  11. Narex Spoon Making Carving Tool - Double Edge

    £28.80
    Narex Spoon Making Carving Tool - Double Edge...
  12. Narex 'Start' Spoon Carving Set

    £69.95
    Spoon carving is a lovely quiet self contained corner of the higly addictive craft of wood carving. You don't need many tools but as always its much easier if they are of good quality and nice and sharp. With a little bit of practice you will soon be able to produce a very acceptable spoon. This set from Narex is designed for complete beginners, it comes with instructions and a roughed out blank of easy carving lime wood so you can get going s...
  13. Narex 'Start' Carving Chisel Set

    £39.50

    Narex have produced an extremely affordable set of 5 starter chisels that do work. The blades are simple sheet steel pressings - but it's the correct grade of steel, and it is properly heat treated so it will take and hold a good edge.

    The Skew chisel, Shallow gouge,Medium gouge, Deep gouge, V-tool are pre-sharpened and come complete with a block of lime wood and clearly written instructions.
    If you want to get into wood car...

  14. Ray Iles Straight Edge Whittling Knife

    £30.00
    Carving green wood into spoons, bowls, kuksa and other items has to be one of life's simplest and most soul nourishing pleasures. It is all the more enjoyable if you have invested in good quality knives that are comfortable to use for long periods. Hand forged O1 carbon steel, carefully heat treated to give a smooth, crisp edge that is both long lasting and easy to maintain. At first glance the beech handles look fairly ordinary, but they f...
  15. Gyokucho 616 Ryoba Seiun Sako (re-saw) 300mm

    £49.00
    The Gyokucho 616 Ryoba is a big Japanese saw suitable for large scale joinery, resawing and dimensioning boards. The 300mm long blade has aggressive tooth patterns on both edges - one for crosscutting, the other for ripping. In either direction it will happily whizz through 4" of beech with impunity. When first starting out with a saw this big, it really pays to take your time and let the saw do the work. The blades of Gyokucho saws are ...
  16. Iwasaki Carving File Half Round Bastard 250mm IW-250HRB

    £38.50
    The Iwasaki IW-250HRB (250mm, halfround, bastard cut) is a coarse toothed file ideal for internal curves on larger work. Ideal for general stock removal tasks like cleaning back to the line after roughing out on the bandsaw, roughing out shaped pieces and adding large ornamental features. Japanese carving files are designed to work with the grain. The tool will work efficiently under its own weight, reducing the pressure as you approach th...
  17. Ray Iles Large Drawknife

    £50.00
    Used for drawing wooden beams, forming dry pegs and adding details like chamfers and lambs tongues, this beautifully forged and ground single bevel drawknife is made by Ray Iles from 01 high carbon steel, and fitted with beech handles and brass ferrules. Wonderful for shave horse work. Blade depth 1-1/2" (40mm) Weight 560g Cutting edge 8-1/2" (220mm) ...
  18. Out of Stock

    Workshop Heaven Fine Woodworking Starter Set

    £310.00

    Choosing which tools to buy first can be a bit daunting, especially if you are new to precision woodworking. This starter set of professional quality hand tools is designed to give you enough tools to complete a few simple projects and exercises, whilst forming a sound base of versatile tools that won't need replacing or upgrading. We haven't included a bench plane, because your physical stature is an important factor in choosing the most ...
Page:
  1. 1
  2. 2
Grid  List 
Loading Image
Loading Image
Loading Image